EN
User manual ............... 2
............... 25
CN
Washing machine
ZWH7120 P
147214520
Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
Installation
This appliance is heavy. Care should be
taken when moving it.
When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
Never pull the power supply cable to remove
the plug from the socket; always take hold of
the plug itself.
All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this
is not adhered to. See relevant section in
the user manual.
Never use the washing machine if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the washing machine is accessible.
After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable.
Child safety
If the machine is situated on a carpeted
floor, please adjust the feet in order to allow
air to circulate freely.
This washing machine is not intended for
use by young children or infirm persons
without supervision.
Always be sure, that there is no water
leakage from hoses and their connections
after the installation.
Young children should be supervised to
ensure that they do not play with the
appliance.
Any plumbing work required to install this
appliance should be carried out by a
qualified plumber.
The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children -
danger of suffocation! Keep them out of
children’s reach
Any electrical work required to install this
appliance should be carried out by a
qualified electrician.
Keep all detergents in a safe place out of
children’s reach.
Make sure that children or pets do not climb
into the drum. To avoid this the machine
incorporates special feature.
Use
This appliance is designed for domestic
use. It must not be used for purposes other
than those for which it was designed.
To activate this
device, rotate the
button (without
pressing it) inside
the door clockwise
until the groove is
horizontal. If
Only wash fabrics which are designed to be
machine washed. Follow the instructions on
each garment label.
Do not overload the appliance. See the
relevant section in the user manual.
necessary use a
coin.
Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and
treat stains such as paint, ink, rust, and
grass before washing. Underwired bras
must NOT be machine washed.
To disable this device and restore the
possibility of closing the door, rotate the
button anti-clockwise until the groove is
vertical.
3
Environment concerns
With adequate pre-treatment, stains and
limited soiling can be removed; the laundry
can then be washed at a lower temperature.
Packaging materials
The materials marked with the symbol
recyclable.
are
Measure out detergent according to the
water hardness, the degree of soiling and the
quantity of laundry being washed.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by
disposing of them properly in appropriate
collection containers.
Old machine
Use authorised disposal sites for your old
appliance. Help to keep your country tidy!
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it shall
be handed over to the applicable collection
point for the recycling of electrical and
electronic equipment.
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise be
caused by inappropriate waste handling of this
product.
For more detailed information about recycling
of this product, please contact your local city
office, your household waste disposal service
or the shop where you purchased the product.
Ecological hints
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
Normally soiled laundry may be washed
without prewashing in order to save
detergent, water and time (the environment
is protected too!).
The machine works more economically if it is
fully loaded.
4
Product description
Front View
Back View
1
2
3
8
9
4
5
6
10
12
11
7
13
11
1
6
7
8
9
Detergent Dispenser Drawer
Worktop
Rating Plate
Water Drain Hose
2
3
4
5
12
13
Hose Holders
Back Feet
Front Feet
Control Panel
Water Inlet Hose
Drain Hose Support
Mains Cable
Door Opening Handle
Drain Filter
10
Technical data
Dimensions
60 cm
85 cm
54 cm
Width
Height
Depth
Power supply voltage/frequency
Total power absorbed
220-240 V/50 Hz
2000 W
Minimum fuse protection
10A
Water supply pressure
Maximum Load
Minimum
Maximum
0,05 MPa
0,8 MPa
Cottons
7.0 kg
2.5 kg
2.5 kg
2.0 kg
Synthetics
Delicates
Hand Wash
Spin Speed
Maximum :
1200 rpm
5
Installation
Unpacking
Important!
Very carefully
remove the front
polystyrene block
(B) by gently
B
All transit bolts and packing must be
removed before using the appliance.
1
pulling the
2
polyethylene bag
(1) downwards
then (2) out,
ensuring not to
tear the bag.
You are advised to keep all transit devices so
that they can be refitted if the machine ever has
to be transported again.
Using a spanner
unscrew and
remove the two
rear bottom
Some models are provided with a bottom
cover that will be found inside the washing
machine drum.
screws.
After ensuring the
polyethylene bags
2
have been
removed, follow
2
below instruction:
Slide out the two
plastic pins.
1
C
(1).
Locate the bottom cover as shown in
position (C).
(2).Then push the top end to lock to the
bottom of washing machine.
Remove the polystyrene base, set the
machine upright and unscrew the remaining
rear screw. Slide
out the relevant
pin.
Lay the machine on its back ensuring that
the hoses are not crushed.
Place one of the
polystyrene angle
packings under
the machine.
Cover all the open
holes with the
plugs which you
can find in the
bag containing
the instruction
booklet.
Remove the
polystyrene block
(A) protecting the
motor.
A
6
Positioning
Install the machine on a flat hard floor.
Water drainage
The end of the drain hose can be positioned in
three ways:
Make sure that air circulation around the
Hooked over the edge of a sink using the
plastic hose guide supplied with the
machine.
machine is not impeded by carpets, rugs etc.
Check that the machine does not touch the
wall or cupboard units.
In this case, make
sure the end cannot
come unhooked when
the machine is
Carefully level by
screwing the
adjustable front feet
in or out.
emptying.
Never place cardboard, wood or similar
materials under the machine to compensate
for any unevenness in the floor.
This could be done by tying it to the tap with a
piece of string or attaching it to the wall.
In a sink drain pipe branch. This branch
must be above the trap so that the bend is
at least 60 cm above the ground.
Water inlet
Connect the water inlet hose to a tap with
3/4” BSP thread.
Directly into a drain pipe at a height of not
less than 60 cm and not more than 90 cm.
Use the hose supplied with the washing
machine. DO NOT USE OLD HOSES.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain
pipe must be larger than the outside diameter of
the drain hose.
The other end of the inlet hose which
connects to the machine can be turned in
any direction.
The drain hose must not be kinked. Run it along
the floor; only the part near the drainage point
must be raised.
Simply loosen the fitting, rotate the hose and
retighten the fitting, making sure there are no
water leaks.
For the correct functioning of the machine
the drain hose must remain hooked on the
proper support piece situated on the top
part of back side of the appliance.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the
tap, you will have to purchase a new, longer
hose specially designed for this type of use.
7
Electrical Connection
Important!
This machine is designed to operate on a
220-240 V, single-phase, 50 Hz supply.
Connect the machine to an earthed socket.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution. Should the
appliance power supply cable need to be
replaced, this should be carried out by our
Service Centre.
“An incorrect power supply may void your
warranty.”
Check that your domestic electrical installation
can take the maximum load required (2.0 kW),
also taking into account any other appliances
in use.
First Use
Run a cotton cycle at 90 °C, without any
laundry in the machine, to remove any
manufacturing residue from the drum and
tub. Pour 1/2 a measure of detergent into
the dispenser drawer and start the machine.
Ensure that the electrical and water
connections comply with the installation
instructions.
Daily Use
Rub particularly soiled areas with a special
detergent or detergent paste. Treat curtains
with special care. Remove hooks or tie them
up in a bag or net.
Sorting the laundry
Follow the wash code symbols on each
garment label and the manufacturer’s washing
instructions. Sort the laundry as follows: whites,
coloureds, synthetics, delicates, woollens.
Removing stains
Before loading the laundry
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Never wash whites and coloureds together.
Whites may lose their “whiteness” in the
wash.
New coloured items may run in the first
wash; they should therefore be washed
separately the first time.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
Make sure that no metal objects are left
in the laundry (e.g. coins, hair clips,
safety pins, pins).
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Remove persistent stains before washing.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long
tapes.
8
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will already have been
damaged and the fabric tends to hole.
Cotton, linen: drum full but not too tightly
packed;
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no
more than one third full.
Mould stains: treat with bleach, rinse well
Washing a maximum load makes the most
efficient use of water and energy.For heavily
soiled laundry, reduce the load size.
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone (*), lay the garment on a soft cloth and
dab the stain.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment. Although biodegradable,
detergents contain substances which, in large
quantities, can upset the delicate balance of
nature.
Lipstick: moisten with acetone (*) as above,
then treat stains with methylated spirits.
Remove any residual marks from white fabrics
with bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
The choice of detergent will depend on the type
of fabric (delicates, woollens, cottons, etc.), the
colour, washing temperature and degree of
soiling.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Only low suds Front load washer detergents
should be used in this appliance:
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
powder detergents for all types of fabric.
powder detergents for delicate fabrics (60
°C max) and woollens,
(*) do not use acetone on artificial silk.
liquid detergents, preferably for low
temperature wash program (60 °C max) for
all types of fabric, or special for woollens
only.
Load the laundry
Open the door by carefully pulling the door
handle outwards.
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash
program.
Place the laundry in
the drum, one item at
a time, shaking them
out as much as
possible. Close the
door.
If using concentrated powder or liquid
detergents, a program without prewash must
be selected.
Any fabric softener or starching additives must
be poured into the compartment marked “
before starting the wash program.
”
Maximum loads
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the MAX mark in the detergent
dispenser drawer.
Recommended loads are indicated in the
program charts. General rules:
9
Do not spray stain pre-treatment products
(e.g. Vanish) on or near the machine, as it
can attack plastic materials reducing its life.
Compartment
used for washing powder or liquid.
: this compartment is
Compartment
: this compartment is used
for fabric conditioner and starching agent.
Quantity of detergent to be used
Aways add laundry detergents before switching
the machine on and keep the dispenser clean
and dry, so that the detergent can be efficiently
dispensed from the unit.
The type and quantity of detergent will depend
on the type of fabric, load size, degree of soiling
and hardness of the water used.
Water hardness is classified in so-called
“degrees” of hardness.
Measure out the detergent and the
fabric softener
Information on hardness of the water in your
area can be obtained from the relevant water
supply company, or from your local authority.
Measure out the amount of detergent required,
pour it into the “main wash” compartment
Follow the product manufacturers’ instructions
on quantities to use.
“
”.
Not enough washing powder causes:
for prewash
the washload to turn grey,
greasy clothes.
for mainwash
Too much washing powder causes:
sudsing,
reduced agitation and washing effect,
inadequate rinsing.
If you wish to carry out the “prewash” phase,
pour it into the compartment marked “
”.
Use less detergent if:
If required, pour fabric softener into the
you are washing a small load,
the laundry is lightly soiled,
compartment marked
must not exceed the “MAX” mark in the
drawer).
(the amount used
large amounts of foam form during washing.
Open the detergent dispenser drawer
The detergent
dispenser is
for softener
divided into three
compartments.
Close the drawer gently.
Compartment
: this compartment is only
used for washing powder when a program
has Prewash or Stain.
10
Control panel
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Program selector dial
Temperature button
Spin button
Extra Rinse Button
Display
Start/Pause button
Delay Start button
Rinse Hold button
Super Quick button
11
Set your washing program
Program selector dial
Turn the program selector dial to the required program. The
green Start/Pause light starts to flash.
The selector dial is divided into following sections:
(Cancelling/Off)
(Cottons)
(Rinse)
(Drain)
(Spin)
(Cottons Prewash)
(Cottons Economy)
(Easy Iron)
(Blanket)
(Mini 30)
(Jeans)
(Synthetics)
(Mixed Fabric)
(Delicates)
(Wool/Handwash)
The selector dial can be turned either clockwise or
anticlockwise. Position “Off” to Reset program/Switching
OFF the machine.
At the end of the program the selector dial must be
turned to position “Off”, to switch the machine off.
Attention!
If you turn the program selector dial to another program
when the machine is working, the red Start/Pause pilot
light will flash 3 times to indicate a wrong selection. The
machine will not perform the new selected program.
Cancelling a program
Turn the selector dial to “Off” to cancel a program which is
running. Now you can select a new program.
Press this button repeatedly to increase or decrease the
temperature, if you want your laundry to be washed at a
temperature different from the one proposed by the
washing machine.
Temperature selector
If a temperature is chosen that is not allowed with the
selected program, the red pilot light of the Start/pause
button will flash 3 times.
12
Press the Spin button repeatedly to change the spin speed,
if you want your laundry to be spun at a speed different from
the one proposed by the washing machine. The relevant
light will light up.
Spin Buttons
Rinse Hold
By selecting this option the water of the last rinse is not
emptied out to prevent the fabrics from creasing.
To empty out the water:
turn the program selector dial to “Off”.
select the Drain or Spin program.
reduce the spin speed if needed, by means of the
relevant button.
depress Start/Pause button.
This option can be used for lightly soiled in order to obtain
a good washing result in a short time.
Super Quick Buttons
The washing time will be reduced according to type of
fabric and the selected temperature.
If an option is chosen that is not allowed with the selected
program, the red pilot light of the Start/Pause button
will flash 3 times.
This option is recommended for people who are
allergic to detergents, and in areas where the water is
very soft.
Extra Rinse Option
The machine performs some additional rinses.
The display shows the following information:
Display
Duration of the selected program.
After selecting a program the duration is displayed in
hours and minutes (for example 2.05).
The duration is calculated automatically on the basis of the
maximum recommended load for each type of fabric.
13
After the program has started, the time remaining is
updated every minute.
Display (continues)
Delayed start
The selected delay (20 hours max) set by means of the
relevant button appears on the display for about 3
seconds, then the duration of the previously selected
program is displayed. The delay time value decreases by
one unit every hour and then, when 1 hours remain, the
time decreases every minute.
Incorrect option selection
If an option which is not compatible with the set wash
programme is selected, the message
is displayed
for about 2 seconds and the integrated red Start/Pause
light start flashing.
Alarm codes
In the event of operating problems, some alarm codes
can be displayed, for example E20 (see paragraph
“Something not working”).
End of programme
When the program has finished a flashing zero is
displayed.
Door open
When the door has not been closed a flashing E40 is
displayed.
To start the selected program, press the “Start/Pause”
button; the corresponding green pilot light stops
flashing.
Start/Pause button
To interrupt a program which is running, depress the
“Start/Pause” button: the corresponding green pilot
light starts to flash.
To restart the program from the point at which it was
interrupted, press the “Start/Pause” button again.
If you have chosen a delayed start, the machine will
begin the countdown.
Delay Start Button
Before you start the program, this option makes it
possible to delay the starting of the washing program by
30 min - 60 min - 90 min, 2 hours and then by 1 hour till
20 hours.
The selected delay time will appear on the display for
about 3 seconds, then the duration of the program will
appear again.
14
The above options must be selected after choosing the
wash program with the dial, and before pressing the
Start/Pause button.
Delay Start Button (continues)
If after having set the delay start option (and pressed
Start/Pause button) and you wish the cancel it,
follow the below steps:
set the washing machine to PAUSE by pressing the
Start/Pause button;
deselect the Delay start option, changing the status;
press the Start/Pause button to start the program.
Important!
The selected delay can be changed only after selecting
the washing program again.
The door will lock through out the delay time.
If you need to open the door, you must first set the
washing machine to PAUSE by pressing the Start/Pause
button, after that you need to wait about 2-3 minutes to
release door lock, the Door Lock (
) pilot light is
flashing to show the door release is in process, pilot light
switch off when the door can be opened.
The “Child Lock” feature will allow you to lock the controls
while the machine is running to prevent tampering.
Child Lock Option (
)
ACTIVATE “Child Lock” by pressing the “Temperature”
and “Spin” buttons about 3 seconds, the padlock
symbol “
” is displayed on the screen.
To DE-ACTIVE “Child Lock” simply press the “Temperature”
and “Spin” buttons about 3 seconds, the “
”padlock
symbol in the screen will disappear.
Child Lock will remain activated until you de-activate it, even
if the machine is turned off.
The machine is provided of an acoustic device, which
sounds in the following cases:
Acoustic Signals Option
when selecting a wash program
when depressing the options buttons
at the end of the cycle
in the event of operating problems
By pressing the “Rinse Hold” and “Super Quick” buttons
simultaneously for about 3 seconds, the acoustic signal is
deactivated (except for the events of operating problems).
By pressing these 2 buttons again, the acoustic signal is
reactivated.
15
Altering an option or a running program Opening the door after the program
has started
It is possible to change any option before the
program carries it out. The option “Super Quick”
cannot be modified after the Start/Pause has
been pressed.
If you need to open the door, you must first
set the washing machine to PAUSE by
pressing the Start/Pause button, after that
you need to wait about 2-3 minutes to
release door lock.
Changing a running program is possible only
by resetting it. Turn the program selector dial
to “Off” and then to the new program position.
The washing water in the tub not be emptied
out. Start the new program by depressing the
“Start/Pause” button again.
If the machine is already heating or the water
level is above the bottom edge of the door or
that the drum is turning. In this case the door
can not be opened.
Interrupting a program
If you can not open the door but you need to
open it you have to switch the machine off by
turning the selector dial to “Off”. After about 3
minutes the door can be opened (pay attention
to the water level and temperature!).
Depress the “Start/Pause” button to interrupt a
program which is running, the corresponding
light starts to flash. Depress the button again to
restart the program.
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Energetic wash
Max.wash
temperature
95 °C
Max.wash
temperature
60 °C
Max.wash
temperature
40 °C
Max.wash
temperature
30 °C
Hand wash
Do not wash
at all
Delicate wash
Bleaching
Ironing
Bleach in cold water
Do not bleach
Hot iron max 200°C
Warm iron max 150°C
Lukewarm iron max 110°C
Do not iron
Dry cleaning
Dry cleaning
in all solvents
Dry cleaning in perchlorethylene,
petrol, pure alcohol, R 111 & R 113
Dry cleaning in petrol,
pure alcohol and R 113
Do not
dry clean
high
temperature
low
temperature
Tumble dry
Do not
tumble dry
Drying
16
Programs informations
To reset a programme and to switch off the machine turn the selector dial
to “Off”. Now, a new programme can be selected.
(Cancelling/Off)
Washing programme for white and coloured cottons fabrics.
Cottons
Cottons
Prewash
select this program if you wish your laundry to be prewashed at 30° C
before the main wash.
select this program if you wish your laundry to be washed is slightly/
normally soiled cottons. This program will obtain good washing results
whilst saving energy.
Cottons
Economy
Synthetics
Washing programme for synthetic or mixed fabrics.
Highly energy efficient cold wash programme for lightly soiled laundry.
This programme requires a detergent which is active in cold water.
Mixed Fabric
Washing programme for delicate fabrics.
Delicates
Washing programme for machine washable wool as well as for hand
washable woollens and delicate fabrics with the “hand washing
symbol.
Handwash/
Wool
” care
With this programme it is possible to rinse and spin cotton garments which
have been washed by hand. The machine performs 3 rinses, followed by a
final spin at maximum speed. The spin speed can be reduced by pressing
Spin button.
Rinse
Drain
Spin
For emptying out the water of the last rinse in programmes with the
“Rinse Hold” option. Turn first the programme selector dial to “Off”, then
select programme Drain and press the Start/Pause button.
Separate spin for hand washed garments and after programmes with
“Rinse Hold” option. Before selecting this programme the selector dial
must be turned to “Off”. You can choose the speed by means of the
relevant button to adapt it to the fabrics to be spun.
Selecting this programme the laundry is gently washed and spun to avoid
any creasing. In this way ironing is easier. Furthermore the machine will
perform some additional rinses. This programme can be used only for
cotton and synthetic fabrics.
Easy Iron
Blanket
Mini 30
Jeans
A gentle program designed for mixed fabrics found in delicate clothes.
Separate programme for lightly soiled synthetics, mixed fabrics and
delicates.
Trousers, shirts or jackets in denim and jersey realized with hi-tech
materials. The Extra Rinse option is activated automatically.
17
Washing programs
Type of laundry
Max.
Load
Program/
Temperature
Description
of program
Options
- Spin Reduction
- Rinse Hold
- Delay Start
- Super Quick
- Extra Rinse
7.0
kg
White, coloured cotton
and linen (Normally
soiled items).: e.g. shirts, Rinses
Main wash at
Cold - 90° C
Cottons
Cold - 90° C
underwear, towels.
Long spin
- Spin Reduction
- Rinse Hold
- Delay Start
- Super Quick
- Extra Rinse
White, coloured cotton
and linen (Heavy soiled
items).: e.g. sheets,
tablecloths, household
linen.
Main wash at
Cold - 90° C
Rinses
7.0
kg
Prewash
Cold - 90° C
Long spin
Main wash at
40° - 60° C
Rinses
White, coloured cotton
and linen (slightly or
normally soiled cotton
items).: e.g. shirts,
blouses, underwear,
towels.
7.0
kg
- Spin Reduction
- Rinse Hold
- Delay Start
- Extra Rinse
Economy
40° - 60° C
Long spin
2.5
kg
- Spin Reduction
- Rinse Hold
- Delay Start
- Super Quick
- Extra Rinse
Synthetic or mixed fabrics Main wash at
(Normally soiled items).: Cold - 60° C
e.g. underwear, coloured Rinses
Synthetics
Cold - 60° C
garments, non-shrink
shirts, blouses.
Long spin
2.5
kg
Mixed fabrics (lightly
soiled laundry).
Main wash at
Cold
Rinses
- Spin Reduction
- Rinse Hold
- Delay Start
- Extra Rinse
Mixed Fabric
Cold
Long spin
Main wash at - Spin Reduction
2.5
kg
Delicate fabrics
Delicates
(Maximum 700 rpm)
- Rinse Hold
- Delay Start
Cold - 40° C
Rinses
Short spin
(Normally soiled items).:
e.g. curtains, acrylics,
viscose, polyester.
Cold - 40° C
- Super Quick
- Extra Rinse
Woollens and hand
washing fabrics.
Main wash at - Spin Reduction
2.0
kg
Handwash/
Wool
- Rinse Hold
- Delay Start
Cold - 40° C
Rinses
Cold - 40° C
Long spin
- Spin Reduction
- Rinse Hold
- Delay Start
- Extra Rinse
Separate rinse cycle for
hand washed items of
cottons.
7.0
kg
Rinses
Long spin
Rinse
18
Type of laundry
Max.
Load
Program/
Temperature
Description
of program
Options
For emptying out the
water left in the drum.
Drain of
water
Not available
7.0
kg
Drain
Spin
- Spin Reduction
- Delay Start
7.0
kg
Separate spin program
for spin out the water
from clothes.
Drain
Long spin
2.5
kg
- Spin Reduction
(Maximum 900 rpm)
- Rinse Hold
Main wash at
Cold - 40° C
Rinses
Easy Iron
Cottons and synthetic
or mixed fabrics.
Cold - 40° C
- Delay Start
Short spin
- Extra Rinse
- Spin Reduction
(Maximum 700 rpm)
- Delay Start
Main wash at
30° - 40° C
Rinses
A gentle program
designed for mixed
fabrics found in delicate
clothes.
7.0
kg
Blanket
30° - 40° C
Short spin
Main wash at
30° C
Rinses
Synthetics and delicates
(lightly soiled items) or
which only needs
- Spin Reduction
(Maximum 700 rpm)
- Delay Start
2.5
kg
Mini 30
30° C
Short spin
freshening up.
2.5
kg
- Spin Reduction
- Rinse Hold
- Delay Start
Trousers, shirts or
jackets in denim and
jersey realized with
hi-tech materials.
Main wash at
Cold - 60° C
Rinses
Jeans
Cold - 60° C
Long spin
* Cottons Economy at 60 °C is recommended for a full load of normally soiled cottons, and is
the water and energy rating label program (in accordance with CEE 92/75 standards).
Care and cleaning
Important!
After each wash
You must DISCONNECT the appliance from the
electricity supply, before you can carry out any
cleaning or maintenance work.
Leave the door open for a while. This helps to
prevent mould and stagnant smells forming
inside the appliance. Keeping the door open
after a wash will also help to preserve the door
seal.
Descaling
The water we use normally contains lime. It is a
good idea to periodically use a water softening
powder in the machine. Do this separately from
any laundry washing, and according to the
softening powder manufacturer's instructions.
This will help to prevent the formation of lime
deposits.
Maintenance Wash
With the use of low temperature washes it is
possible to get a build up of residues inside
the drum. We recommend that a maintenance
wash be performed on a regular basis.
19
use a small brush
to clean the recess.
To run a maintenance wash:
The drum should be empty of laundry.
Select the hottest cotton wash program.
Use a normal measure of detergent, must be
a powder with biological properties.
External cleaning
Replace the drawer and run the rinse programme
without any clothes in the drum.
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Cleaning the dispenser drawer
Cleaning the drain filter
The washing powder and additive dispenser
drawer should be cleaned regularly.
Drain filter collects lint and other items left in the
dirty laundry to prevent pump blockage
Remove the drawer
by pressing the
catch downwards
and by pulling it out.
The pump must be cleaned regularly. To clean
the filter, proceed as follows:
Turn programme selector dial to position Off
(Off).
Unplug the appliance.
Open the door.
Turn the drum and align the filter cover
(FILTER) with the arrow on the door seal.
Flush it out under a tap, to remove any traces
of accumulated powder.
To aid cleaning,
the top part of
the additive
compartment
should be
removed.
Open the filter cover by pressing the special
hook and by rotating the cover upwards.
Cleaning the drawer recess
Having removed the drawer, use a small brush
to clean the recess, ensuring that all washing
powder residue is removed from the upper and
lower part of the recess.
Press here
20
Hold filter securly
and pull upwards to
remove it from its
position.
close the filter
cover.
insert the mains
plug again.
Remove eliminate the
eventual fluff or small
objects around the
filter.
Important!
Do not start washing clothes without the
filter in its place.
Clean the filter under
the water tap.
Cleaning the water inlet filter
If your water is very hard or contains traces of
lime deposit, the water inlet filter may become
clogged.
After cleaning the
filter, open the filter
cover and insert the
filter back to its
position.
It is therefore a good idea to clean it from time
to time.
Turn off the water
tap.
Unscrew the water
inlet hose.
Clean the filter
using a hard bristle
brush.
Important!
Tighten up the inlet
hose.
The filter is inserted correctly when the
indicator on this top is visible and you
will hear “Click” sound.
21
Something not working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily
without calling out an engineer. Before contacting your local Service Centre, please carry out the
checks listed below.
During machine operation it is possible that the red Start/Pause pilot light flashes to indicate that
the machine is not working.
Once the problem has been eliminated, press the Start/Pause button to restart the program. If
after all checks, the problem persists, contact your local Service Centre.
Malfunction
Possible cause
Solution
The door has not been closed.
Close firmly the door.
(Red Start/Pause pilot light flashes)
The plug is not properly inserted in
the power socket.
Insert the plug into the power
socket.
There is no power at the socket.
Please check your domestic
electrical installation.
The washing
machine does
not start:
The selector dial is not correctly
positioned and the Start/Pause
button has not been depressed.
Please turn the selector dial and
press the Start/Pause button
again.
The delay start has been selected.
If the laundry are to be washed
immediately, cancel the delay
start.
The water tap is closed.
Open the water tap.
(Red Start/Pause pilot light flashes)
The inlet hose is squashed or kinked. Check the inlet hose connection.
(Red Start/Pause pilot light flashes)
The machine
does not fill:
The filter in the inlet hose is blocked. Clean the water inlet hose filter.
(Red Start/Pause pilot light flashes)
The door is not properly closed.
Close firmly the door.
(Red Start/Pause pilot light flashes)
The machine fills
then empties
immediately:
The end of the drain hose is too low. Refer to relevant paragraph in
“water drainage” section.
The drain hose is squashed or kinked. Check the drain hose connection.
(Red Start/Pause pilot light flashes)
The drain filter is clogged.
(Red Start/Pause pilot light flashes)
Clean the drain filter.
The machine
does not empty
and/or does not
spin:
The option Rinse Hold has been
selected.
Disable the option Rinse Hold or
select Spin program.
The laundry is not evenly distributed
in the drum.
Redistribute the laundry.
22
Malfunction
Possible cause
Solution
Too much detergent or unsuitable
detergent (creates too much foam)
has been used.
Reduce the detergent quantity or
use another one.
Check whether there are any leaks
Check the water inlet hose
from one of the inlet hose fittings. It is connection.
not always easy to see this as the
water runs down the hose; check to
see if it is damp.
There is water on
the floor:
The drain hose is damaged.
Change it with a new one.
Too little detergent or unsuitable
detergent has been used.
Increase the detergent quantity or
use another one.
Stubborn stains have not been
treated prior to washing.
Use commercial products to treat
the stubborn stains.
Unsatisfactory
washing results:
The correct temperature was not
selected.
Check if you have selected the
correct temperature.
Excessive laundry load.
Introduce into the drum less
laundry.
The program is still running.
Wait the end of washing cycle.
The door will not
open:
The door lock has not been released. Wait about 3 minutes.
There is water in the drum.
Select drain or spin program to
empty out the water.
The transit bolts and packing have
not been removed.
Check the correct installation of
the appliance.
The support feet have not been
adjusted.
Check the correct levelling of the
appliance.
The machine
vibrates or is
noisy:
The laundry is not evenly distributed
in the drum.
Redistribute the laundry.
Maybe there is very little laundry in the Load more laundry.
drum.
Unstable floors eg. wooden floors.
The machine is fitted with a type of
motor which makes an unusual noise
compared with other traditional
motors. This new motor ensures a
softer start and more even distribution
of the laundry in the drum when
spinning, as well as increased stability
of the machine.
The machine
makes an unusual
noise:
23
Malfunction
Possible cause
Solution
The electronic unbalance detection
device has cut in because the
Redistribute the laundry.
laundry is not evenly distributed in
the drum. The laundry is redistributed
by reverse rotation of the drum. This
may happen several times before the
unbalance disappears and normal
spinning can resume. If, after 10
minutes, the laundry is still not evenly
distributed in the drum, the machine
will not spin. In this case, redistribute
the load manually and select the spin
programme.
Spinning starts
late or the
machine does not
spin:
Machines based on modern
technology operate very
economically using very little water
without affecting performance.
No water is visible
in the drum:
If you are unable to identify or solve the problem, contact our service centre. Before
telephoning, make a note of the model, serial number and purchase date of your machine,
the Service Centre will require this information.
Model description (MOD.).......................
Product number (PNC) ...........................
Serial number (S.N.) ...............................
24
|