FREEZER
ZV 45 R
ZV 45 RAL
INSTRUCTION BOOKLET
2222690-96
Important Safety Instructions
These warnings are provided in the interests of your safety. Ensure that you understand them all before
installing or using this appliance. Your safety is of paramount importance.
If you are unsure about any of the meanings of these warnings contact the Customer Care Departement.
Prior to Installation
During Use
■ Check the appliance for transport damage. Under
no circumstance should a damaged appliance be
installed. In the event of damage please contact
your retailer.
■ This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs
only. It is not intended for commercial or industrial
use.
■ Containers with flammable gases or liquids can
leak at low temperatures. Do not store any
containers with flammable materials, such as
spray cans, fire extinguisher refill cartridges etc.
in the refrigerator.
Installation
■ This appliance is heavy. Care should be taken
when moving it.
■ It is dangerous to alter the specifications or
■ Frozen food should not be refrozen once it has
attempt to modify this product in any way.
thawed out.
■ Ensure that the appliance does not stand on the
electrical supply cable.
■ Do not place carbonated or fizzy drinks in the
freezer compartment.
Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly
available from the manufacturer or its service
agent.
■ Ice lollies can cause ‘frost/freezer burns’ if
consumed straight from the freezer.
■ Do not remove items from the freezer
compartment if your hands are damp/wet, as this
could cause skin abrasions or frost/freezer burns.
■ Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
■ Bottles and cans must not be placed in the
freezer compartment they can burst when the
contents freeze.
■ Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the required
distance for ventilation, as stated in the
installation instructions.
■ Manufactures’ recommended storage times
should be adhered to.Refer to relevant
instructions.
■ The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Maintenance and Cleaning
■ Before cleaning, always switch off the appliance
and disconnect from the electrical supply.
Refrigerant
■ When unplugging always pull the plug from the
■ The refrigerant isobutane (R600a) is contained
within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental
compatibly, which is nevertheless flammable.
mains socket, do not pull on the cable.
Servicing
■ This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
■ During transportation and installation of the
appliance, be certain that none of the
components of the refrigerant circuit become
damaged.
■ Under no circumstances should you attempt to
repair the appliance yourself. Repairs carrier out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local
Service Force Centre.
■ If the refrigerant circuit should become damaged:
- avoid open flames and sources of ignition.
- thoroughly ventilate the room in which the appli-
ance is situated.
Child Safety
■ Do not allow children to tamper with the controls
At the end of the Appliance Life
■ When disposing of your appliance use an
or play with the product.
authorised disposal site.
■ There is a risk of suffocation! Keep packaging
■ Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
material away from children!
3
Description of the Appliance
1
2
3
S
4
5
6
A
B
D
C
A - Freezer controls
B - Freezer calendar (reccomended storage times for frozen foods)
C - Freezer food storage
D - Freezing fresh food
4
Operation
Before use
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water). Do not use soap or
detergent as the smell may linger. Dry thoroughly.
Freezer controls
1
2
3
S
4
5
6
A B C D
E
A - Fast freeze switch
B - Fast freeze light (yellow)
C - Mains-on light (green)
D - Warning light (red)
E - Thermostat control
When the freezer is first switched on, the warning
light will stay on until the temperature has dropped to
a safe level for the storage of frozen food.
Start your appliance
Insert the plug into the wall socket. The pilot light
(C) will light up to show that the appliance is on.
Freezing fresh food
In any 24 hour period you can freeze up to 18 kg of
fresh food.
Temperature control
The temperature within the freezer is controlled by
the thermostat situated at the top of the cabinet (E).
To operate the freezer proceed as follows:
Turn the thermostat control beyond the «O» position.
When you first start the freezer, we suggest that you
turn the thermostat control to a medium setting. For
easier turning of this control, use a small coin.
The internal temperature of the freezer is
automatically adjusted by the thermostat to ensure
safe food storage. However, if the appliance is
working in unfavourable room conditions such as
poor ventilation, high temperature and frequent door
openings, it may be necessary to select a more
suitable setting.
When you first start the freezer, or after a period of
non-use, slide the fast-freeze switch (A) to the left
(fast freeze position) 2-3 hours before you want to
freeze your food (the yellow light (B) lights up).
If the freezer is already in operation, the fast-freeze
switch should be activated about 24 hours before
freezing fresh food. This time can be shortened,
depending on the quantity of food to be frozen. After
the time has elapsed place the food to be frozen in
the top compartments of the freezer as this is the
coldest part.
Once the food is completely frozen (which could take
up to 24 hours) return the fast freeze switch to the
«OFF» position; the yellow light (B) goes out.
Distribute the frozen food packages in the other
compartments, so that the top compartment can be
used for a further freezing operation.
To obtain a lower temperature, turn the thermostat
control to the higher numbers; to obtain a higher
temperature turn the control to the lower numbers.
Only freeze top quality, fresh and thoroughly cleaned
foodstuffs.
Do not allow fresh food to touch food which is
already frozen.
During the freezing process, ensure that the freezer
door remains closed.
Warning light (red)
If the temperature warning light (D) lights up, it
indicates that the temperature within the freezer has
reached a level where safe food storage is no longer
ensured.
5
Frozen food storage
Thawing
When you first start the freezer or if the freezer has
been out of use for some time, we advise you to run
your appliance for at least two hours in the «fast
freeze» mode before storing frozen food.
Deep frozen or frozen food, prior to being used, can
be thawed in the fridge or at room temperature
depending on the time available. Small food items
may even be cooked from frozen; in this case
cooking will take longer.
To obtain the best performance from this appliance,
we strongly recommend that you make sure that the
commercially frozen foodstuffs were adequately
stored by the retailer and, furthermore, be sure that
these frozen foodstuffs are transferred from the
foodstore to the consumer in the shortest possible
time (a temperature increase of the frozen food
could shorten its storage period).
Any frozen food which is allowed to thaw
accidentally should either be eaten as soon as
possible or thrown away. Alternatively, if the food is
uncooked and has not been completely defrosted it
can be cooked and then refrozen.
Defrosted cooked food must never be refrozen.
It is also advisable not to exceed the storage period
indicated by the producer of the food.
Ice making
Finally, do not open the door frequently or leave it
open longer than is absolutely necessary.
Fill the ice tray with water to the top of each ice cube
compartment, and place it in the freezer. To release
the ice cubes, twist the tray along its length. Never
use a sharp instrument to remove ice from the tray.
Important
Do not put carbonated liquids, (fizzy drinks
etc.), in the freezer compartment.
Water ices, if consumed immediately after
removal from the freezer, can possibly
result in a low temperature skin burn.
Normal Operating Sounds
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils or
tubing at the rear, to the fixed freezer shelves.
Do not remove items from the freezer if
your hands are damp/wet, as this could
cause skin abrasions or "frost/freezer
burns".
When the compressor is on, the refrigerant is being
pumped round, and you will hear a whirring sound or
pulsating noise from the compressor.
If there is a power failure during the storage
of frozen food, do not open the door during
the whole time of the power failure. If the
freezer is fully loaded, the frozen food will
not be affected if the power cut is of short
duration; otherwise, it is recommended to
consume the food within a very short time.
A thermostat controls the compressor, and you will
hear a faint ‘click’ when the thermostat cuts in and
out.
6
Health and Safety Guidelines
Because of consumer demand, preservatives have been removed from many pre-prepared food. This
together with the changes in shopping habits to a once-a-week shop, mean that safe handling and
storage of food is even more important than ever.
The following tips should help you to ensure that the food in your home is in as perfect condition as
possible.
■ Keep the freezer door closed as much as
■ Never place hot food, bottles or cans of fizzy
drink in the freezer as they may explode.
Containers with a lid must not be filled to the
brim.
possible.
■ Do not push food together too much, try to allow
air to circulate around each item.
■ Do not open the door or place extra fresh food in
the freezer next to food which is already frozen
as this could cause the temperature of the frozen
food to rise and its quality and storage life to
reduce.
■ Cool cooked food as quickly as possible but do
NOT place in the freezer until cool. (Leave food
in a cool place in order that it can then be placed
in the refrigerator as soon as possible).
■ Do not store food uncovered.
■ The best way to defrost food is to put it in the
refrigerator to thaw slowly.
■ Ensure that food placed in the freezer is dated
and labelled and used in date order to ensure
that food is consumed at its best.
■ It is important that food is used before its “best
before” date.
■ Always wash your hands with soapy water and
dry them with a clean towel before handling food.
■ Keep work surfaces clean and avoid cross
contamination by not using the same work
surface or knife, without washing them thoroughly
in between.
■ The foods to be frozen must be fresh and of the
best quality.
■ The size of each pack should be small enough to
ensure that it is used in one go. Small packs
freeze more quickly and uniformly and give better
results.
■ Frozen food, once thawed, must not be refrozen.
Lean food keeps better and longer than fatty
food, salt reduces the storage time.
■ Wrap the food in polythene or aluminium freezing
bags or foil so that they adhere to the food and
provide an airlight seal.
■ Packaging which is swollen or has traces of
refrozen water droplets on the pack could
indicate that the product has not been kept at a
suitable temperature and that it may have lost its
original quality. Partially thawed food must not be
refrozen, it must be consumed within 24 hours.
Never exceed the storage time indicated.
7
Defrosting
The freezer compartment will become progressively
covered with frost. This should be removed with the
special plastic scraper provided, whenever the
thickness of the frost exceeds 1/4".
During this operation it is not necessary to switch off
the power supply or to remove the foodstuffs.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
and it is advisable to carry out this operation when
the appliance is empty.
To carry out complete defrosting proceed as follows:
1. Remove any stored food, wrap it in several layers
of newspaper and put it in a cool place.
2. Turn the thermostat control (E) to the «O» setting.
3. Leave the door open.
4. Introduce the plastic scraper in the appropriate
seating as shown in the figure and place
underneath a basin to collect the defrost water.
5. When defrosting is completed, dry the interior
D068
thoroughly.
Turn the thermostat control to a medium setting
between 2 and 4 and, after letting the appliance run
for at least two hours in the «fast freeze» mode,
replace the previously removed food into the
compartments.
Important
Important
In the event of a power failure causing
the temperature within your freezer to
rise, do not re-freeze the food without
checking its condition. The following
guidelines should assist you:
A temperature rise of the frozen food packs
during defrosting may shorten their
storage life.
Never use sharp metal tools to scrape off
frost from the evaporator as you could dam
age the appliance beyond repair.
Ice-cream: once thawed should be
discarded.
Fruits & Vegetables: if soft should be
cooked and used up.
Breads & Cakes: can be re-frozen without
danger.
Shellfish: should be refrigerated and used
up quickly.
Cooked Dishes: i.e. casseroles should be
refrigerated and used up.
Large Pieces of Meat: can be re-frozen pro
viding there are still ice crystals remaining
within them.
Small Joints: should be cooked and can
then be re-frozen as cooked dishes.
Chicken: should also be cooked and re-
frozen as a cooked dish.
8
Maintenance and Cleaning
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
Warning
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging
must therefore only be carried out by
authorised technicians.
Internal cleaning
Clean the inside and accessories with warm water and
bicarbonate of soda (5ml to 0.5 litre of water). Rinse
and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE POWDERS,
HIGHLY PERFUMED CLEANING PRODUCTS OR
WAX POLISHES, TO CLEAN THE INTERIOR AS
THESE WILL DAMAGE THE SURFACE AND LEAVE
A STRONG SMELL.
External cleaning
Wash the outer cabinet door with warm soapy water.
Do NOT use abrasive products.
CONDENSER
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance, with
a brush or vacuum cleaner, see figure.
You MUST ensure that the appliance is switched OFF.
An accumulation of dust will affect the performance of
the appliance and cause excessive electricity
COMPRESSOR
D358
consumption.
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all foods
and clean the appliance, leaving the door ajar to
prevent unpleasant smells.
9
Something not Working?
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation a charge will be made, even if the appliance is under guarantee.
Before contacting your local Service Force Centre check the following points.
Symptom
Solution
No power to appliance
- Check there is power at the socket.
- Check there is not a power cut by checking the
household lights.
- Check the fuse has not blown.
The temperature in the freezer is too high
- Check the thermostat is turned to the correct
setting relative to ambient conditions.
- Check the ambient temperature is within the appliances
operating limits of 10°C to 32°C.
Relocate the appliance if necessary.
The freezer door will not open
- Has door just been opened?
If so leave for a few minutes to allow the air pressure to
equalise.
The compressor runs continuously
- Adjust the thermostat to give correct temperature
control. See page 5.
- Check that the door is closed.
- Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
- Check that air ventilation is not obstructed.
Excessive frost and ice has built up.
- Ensure the door is not left open.
- Check that nothing is preventing the door from closing.
Is the door gasket intact and clean.
- Has advised periodic defrosting been carried out.
- Refer to normal operating sounds.
Noise
If after the above checks, there is still a fault, call your local Service Force Centre.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee service calls.
10
Service and Spare Parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts please contact
your local Zanussi Service Force Centre by
telephoning:
Before calling out an engineer, please ensure you
have read the details under the heading ‘Something
Not Working?’
When you contact the Service Centre you will need
to give the following details.
1. Your name, address and post code
2. Your telephone number
08705 929929
3. Clear and concise details of the fault
Your call will be routed to the Service Force Centre
covering your post code area.
4. The model serial no. of the appliance (found on
the rating plate)
5. The purchase date
Customer Care Department
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, you
are invited to contact our Customer Care Department by letter or telephone as follows:
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727727
11
Guarantee Conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of purchase this Zanussi appliance or any
part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option
repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
■
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
■
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's
instructions.
■
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorised by us.
■
■
■
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
Any appliance or defective part replaced shall become the Company's property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
■
■
■
■
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
■
The guarantee starts from the date you first purchased your product.
■
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
■
■
■
This guarantee relates to you and cannot be transferred to another user.
Your new home is within European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
■
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look after
you and your appliance.
France
Germany
Italy
Senlis
+33 (0) 44 62 29 99
+49 (0) 911 323 2600
+39 (0) 1678 47053
+46 (0) 8 738 79 50
+44 (0) 1753 219897
Nurenberg
Pordenone
Stockholm
Slough
Sweden
UK
12
Technical specifications
DIMENSIONS
Height
Width
Depth
85
54,5
60
cm
cm
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
220-240 V / 50 Hz
85 W
AVERAGE DAILY UNITS ELECTRICITY
0,95 kWh
GROSS CAPACITY
NET CAPACITY
STAR RATING
125 l
104 l
Installation
Positioning
For this appliance to work efficiently, it should be
located away from heat sources, e.g. cookers,
radiators, boilers, direct sunlight etc. This also
includes locations or rooms where the ambient
temperature reaches above 32 degrees C or drops
below 10 degrees (e.g. conservatories).
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
must also be a minimum distance beween the top of
the cabinet and any overhanging kitchen furniture as
shown in the figure.
Do not obstruct the space underneath. The back of the
cabinet may be placed close to the wall but must not
touch it. DO NOT install in places with restricted
ventilation.
A
B
NP006
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers.
D200
13
Electrical Connection
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
WARNING:
THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability
should this safety measure not be
observed.
This appliance complies with the following
E.E.C. Directive:
- 73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent amendments.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
- 89/336 EEC of 3.5.89 (Electromagnetic
- Compatibility Directive) and subsequent amend-
ments.
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of breakdown.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
If you fit your own plug, the colours of the wires in
the mains lead of your appliance, may not
correspond with the markings identifying the
terminals in your plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
Connect the Green and the Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
yellow.
, or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
BROWN
BLUE
CORD CLAMP
D207
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or colured
red.
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BS1362 fuse. Only
ASTA or BSI approved fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
A replacement cover/carrier must be obtained from
your local Electrolux Service Force Centre whose
address is listed in the Customer Care Booklet
which accompanies your instruction manual.
14
Door Reversal
Before carrying out the operations described below,
pull out the mains plug from the wall socket.
To carry out this reversal go through the following
steps:
1. Gently lay the appliance on its back with the top
held away from the floor by 5-8 cm (2-3 inches) of
packing.
2. Remove the bottom door hinge (5).
3. Remove the door (4) by opening it and pulling it
gently downwards to remove it from the top hinge
pin (2).
4. Unscrew the top hinge pin (2) from the top hinge (1)
and replace it in the opposite hole on the left hand
side.
5. Unscrew the foot at the base (6) of the appliance
and refit it on the opposite side.
6. Refit the door and the bottom hinge to the left hand
side.
When the bottom hinge is screwed in, a certain
amount of force is exerted on the screws.
It is therefore advisable to lubricate the screw tips
before starting this operation.
Important
After completion of the door reversal opera-
tion, verify that the door gasket is sealing
onto the cabinet.
15
|