Planning Information
Pro Low-Profile Wall Ventilation Hood
M O D E L P W 3 0 2 2 1 0 ( R )
Hand finished
craftsmanship
Classic stainless
steel finish
Stainless steel
baffle filters
Decorative rail
(optional)
Model PW302210
Location of
rating plate
Model PW302210R
Rail Option
Welded seams
and hemmed edges
Recessed easy-
access controls
Halogen lighting
Infinite-speed
blower control
Model PW302210R shown with decorative rail.
Wolf Pro wall hoods provide the ultimate in
ventilation. With standard elements like heat sentry
and dual setting halogen lighting, Wolf elevates the
need for ventilation to an enjoyable perk.
Wolf Pro low-profile wall hoods are
10" (254) high by 22" (559) deep and
come in the classic stainless steel finish.
Rail option hoods (R) come with a classic
stainless steel decorative rail and stand-
offs. Optional platinum or brass rails
match dual fuel range bezels. Pro wall
hoods are sold as a shell only; internal,
in-line and remote blower options are
available.
Pro low-profile wall hoods are available in the classic
stainless steel finish. You also have the option of a
decorative rail. While a classic stainless steel rail is
standard on (R) models, platinum or brass rails are
available to match the bezels of our dual fuel ranges
and sealed burner rangetops.
Pro wall ventilation hoods are recommended for use
with all Wolf cooking appliances. For optimal perform-
ance, a Pro 27" (686) deep wall hood is recommended
for use with ranges and rangetops that contain a
charbroiler or griddle.
Dimensions in parentheses are in
millimeters unless otherwise specified.
1
9/07
Planning Information
Pro Low-Profile Wall Ventilation Hood
M O D E L P W 3 0 2 2 1 0 ( R )
B L O W E R O P T I O N S
500 CFM Internal Blower
600 CFM In-Line Blower
600 CFM Remote Blower
900 CFM Remote Blower
S P E C I F I C A T I O N S
810991
808331
801640
801641
Overall Width of Hood
Overall Height of Hood
30" (762)
10" (254)
Overall Depth of Hood
(including rail)
22" (559)
24" (610)
Internal Blower Option
In-Line Blower Option
Remote Blower Options
Discharge
500 CFM
600 CFM
Refer to Pro Ventilation Recommendations
at the end of this section.
600 or 900 CFM
Vertical or Horizontal
10" (254) Round
A C C E S S O R I E S
Platinum or brass decorative rail
and stand-offs
Duct Size
Electrical Supply Requirements
110/120 V AC, 60 Hz
15 amp dedicated circuit
38" (965) high classic stainless
steel backsplash with or without
warming racks
Shipping Weight (shell only)
59 lbs (27 kg)
6" (152), 12" (305), 18" (457) and
24" (610) classic stainless steel
duct covers
Specifications are subject to change without notice.
Transitions for both 8" (203) and
10" (254) round duct
Recirculating kit
Accessories are available through your
Wolf dealer. To obtain local dealer
information, visit the Showroom Locator
section of our website, wolfappliance.com.
Dimensions in parentheses are in
millimeters unless otherwise specified.
3
Planning Information
Pro Low-Profile Wall Ventilation Hood
M O D E L P W 3 0 2 2 1 0 ( R )
I N S T A L L A T I O N S P E C I F I C A T I O N S
LOCATION OF
ELECTRICAL
6"
E
(152)
5"
10" (254)
HEIGHT
(127)
OF HOOD
30" (762)
WIDTH OF HOOD
30" TO 36"
(762–914)
30" TO 36"
(762–914)
22" (559)
DEPTH OF HOOD
TO COUNTERTOP
TO COUNTERTOP
NOTE: Pro low-profile hoods have an adjustable discharge.
D I M E N S I O N S
Overall Width of Hood
30" (762)
Overall Height of Hood
10" (254)
22" (559)
Overall Depth of Hood (excluding rail)
Countertop to Bottom of Hood
Location of Electrical
30" (762) to 36" (914)
Within shaded area
See Installation Instructions shipped with unit for detailed specifications.
Dimensions in parentheses are in
millimeters unless otherwise specified.
4
Planning Information
Pro Low-Profile Wall Ventilation Hood
M O D E L P W 3 0 2 2 1 0 ( R )
I N S T A L L A T I O N N O T E S
Refer to the illustrations and specifications
IMPORTANT NOTE: Install this ventilation hood
for overall dimensions and installation specifics.
only with a Wolf blower.
Wolf Pro wall ventilation hoods are recom-
mended for use with any Wolf cooking appli-
ance, and should be as least as wide as the
cooking surface. It is recommended that the
hood overlap the cooking surface by 3" (76) on
either side.
Pro wall hoods require a separate, grounded
110/120 V AC, 60 Hz power supply. The service
should have its own 15 amp circuit breaker.
Placement of the electrical supply is not critical,
as long as you provide enough 120 V AC, 60 Hz
power cable to make the electrical connection.
Locate electrical within the shaded area shown
in the Installation illustration on page 4.
IMPORTANT NOTE: For optimal performance, a
Pro 27" (686) deep wall hood is recommended
for use with ranges and rangetops that contain
a charbroiler or griddle.
You must follow all National Electrical Code
regulations. In addition, be aware of local codes
and ordinances when installing your service.
Installation of all Pro ventilation hoods
should be 30" (762) to 36" (914) from the
bottom of the hood to the countertop. Follow
the dimensions shown in the Installation
illustration on page 4.
Refer to the installation instructions shipped
with each Wolf product for detailed specifica-
tions. This information can also be found on
our website, wolfappliance.com.
Wolf Pro wall hoods are shipped without a
blower assembly. Internal, in-line or remote
blower assemblies are available. Blower options
also vary with the volume of air that needs to
be moved and the length of the duct run. Refer
to the charts at the end of this section for Pro
ventilation recommendations and blower
options.
Dimensions in parentheses are in
millimeters unless otherwise specified.
5
Planning Information
Pro Low-Profile Wall Ventilation Hood
M O D E L P W 3 0 2 2 1 0 ( R )
D U C T I N G C O N S I D E R A T I O N S
Wolf Pro low-profile wall hoods are shipped
without the blower assembly. Internal, in-line
and remote blower assemblies are available.
The hood will operate most efficiently when
ductwork does not exceed 50' (15 m) in length.
Local building codes may require the use of
make-up air. Consult your local HVAC professional
for specific requirements in your area.
IMPORTANT NOTE: Install this ventilation hood
only with a Wolf blower.
Pro low-profile wall hoods come standard with
a horizontal or vertical discharge. No transition is
included. Internal blower WBLOWER-50INT
comes with a transition. When using an in-line
or external blower, use the optional accessory
10" (254) round transition.
IMPORTANT NOTE: Wolf Pro low-profile wall
hoods must be vented to the outside except when
used with the accessory recirculating kit with the
600 CFM blower. Use only metal ductwork.
Refer to the illustration below for ducting
considerations for Pro low-profile wall hoods.
Ducting for Pro
low-profile wall hoods.
DUCTWORK INSTALLATION
THROUGH ROOF
ROOF CAP OR REMOTE BLOWER
10" (254) ROUND DUCT
ACCESSORY TRANSITION
FOR IN-LINE OR
SOFFIT OR CABINET
OR DUCT COVER
REMOTE BLOWER
173/4"W x 41/4"D TO 10" ROUND
93/8"H (INCLUDING FLANGES)
VERTICAL DISCHARGE
10" (254)
HEIGHT OF HOOD
WALL HOOD
22" (559)
DEPTH OF HOOD
30" TO 36"
(762–914)
COUNTERTOP
TO BOTTOM OF
VENTILATION HOOD
36" (914)
STANDARD
FLOOR TO
COUNTERTOP
HEIGHT
NOTE: 10" (254) ROUND ACCESSORY TRANSITION SHOWN IN VERTICAL DISCHARGE APPLICATION WITH
IN-LINE OR REMOTE BLOWER. REFER TO INSTALLATION INSTRUCTIONS FOR HORIZONTAL DISHCARGE.
Dimensions in parentheses are in
millimeters unless otherwise specified.
6
Planning Information
Pro Low-Profile Wall Ventilation Hood
M O D E L P W 3 0 2 2 1 0 ( R )
W O L F B L O W E R A S S E M B L I E S
A ventilation system must include a blower
assembly. Wolf ventilation hoods are shipped
without the blower assembly. An internal, in-line
or remote blower assembly must be selected to
accommodate the cooking appliance, CFM
requirements and homeowner preferences.
Internal, in-line and remote blower assemblies
are available as sales accessories through your
Wolf dealer.
Internal blowers are mounted inside the hood
canopy. In-line blowers are mounted in between
the hood and the exterior of the home. Remote
blowers can be mounted on the roof or in some
cases, on an exterior wall. Refer to the illustra-
tions below for dimensions of Wolf in-line and
remote blowers.
Pro ventilation recommendation charts on the
following page provide minimum CFM recom-
mendations according to the cooking appliance
and ventilation hood used and blower options
for each specific Pro low-profile wall hood.
IMPORTANT NOTE: Use only a Wolf blower
with all Wolf ventilation products.
3
20 /4"
(527)
1
3
28 /4"
24 /8"
(718)
(619)
10" (254)
Diameter
3
11 /4"
1
15 /2"
(394)
(298)
1
24 /2"
1
(622)
18 /2"
(470)
1
4 /2"
(114)
14"
(356)
1
21 /2"
3
4
/4"
1
(546)
12 /4"
(311)
3
(121)
24 /4"
(629)
In-line BLOWER-60IL
Remote BLOWER-60REM and
BLOWER-90REM
Unit dimensions may vary by 1/8" (3).
Dimensions in parentheses are in
millimeters unless otherwise specified.
7
Planning Information
Pro Low-Profile Wall Ventilation Hood
M O D E L P W 3 0 2 2 1 0 ( R )
P R O V E N T I L A T I O N C F M R E C O M M E N D AT I O N S
Pro Low-Profile Wall Hoods
Model
PW302210
PW362210
500/600
900
PW422210
PW482210
DF304 / R304 / SRT304
DF366 / R366 / SRT366 / RT366
DF364 / R364 / SRT364 / RT364
RT362
500/600
900
900
900
900
900
DF484 / R484 / SRT484 / RT484
900
Minimum CFM requirements for Wolf ranges and rangetops. CFM recommendations are based on total Btu/hr output.
Additional CFM may be required for long duct runs.
P R O V E N T I L A T I O N B L O W E R O P T I O N S
Pro Low-Profile Wall Hoods
Blower Description
500 CFM Internal
600 CFM In-Line
600 CFM Remote
900 CFM Remote
Blower Number
Wall Hood Models
WBLOWER-50INT (810991)
BLOWER-60IL (808331)
BLOWER-60REM (801640)
BLOWER-90REM (801641)
PW302210 / PW362210
All Low-Profile Wall Hoods
All Low-Profile Wall Hoods
All Low-Profile Wall Hoods
Dimensions in parentheses are in
millimeters unless otherwise specified.
8
|