®
WINEGARD
TM
Movin’ View
Mobile Digital Satellite Antenna
Model MV-3500
U.S. Patent Nos. 6,023,247; 6,188,300
Made in the U.S.A.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
Printed in U.S.A. © Winegard Company 2004 2451019 11/9/04
1
Quick Reference Guide
NOTICE!
This model is PRESET for DIRECTV® receivers.
®
®
If you have a DISH Network or ExpressVu (Canada) receiver, you
must change the numbered switches inside the dome.
TO CHANGE SWITCHES INSIDE DOME —
1. Remove screws holding dome to base and remove dome. Place dome in safe spot to avoid damage.
Switches will be set at 101° for DIRECTV. You will be changing these switches.
(#1 represents Switch DOWN; #0 represents Switch up)
1
2
3
4
5
6
7
8
Sat. Rcvr.
Switch Set Position
1
2
3
4
5
6
7
8
DISH NETWORK
DIRECTV
0
0
0
1
0
0
1
1
0= UP
0
0
0
0
0
0
0
1
(FACTORY PRESET)
1= DOWN
ExpressVu
0
1
0
1
1
0
1
1
2. Determine which programming you will be using. This will determine how you set your switches.
For DISH Network®, set switches to 119°.
For ExpressVu, set switches to 091°.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
0= UP
0= UP
1= DOWN
1= DOWN
DIRECTV receivers must be set to the two satellite, oval dish setting. Refer to your receiver manual.
DISH Network receivers must either have the check switch set for SW42 or unknown, no satellite found. See
page 4.
Operation (Vehicle MUST be stationary!!)
4. Once the unit has acquired GPS, the dish will
begin its search.
a. The dish will pause on the signal long enough to
determine which satellite it has found.
1. Turn on receiver and television set. The MV-3500
must be connected to a receiver that is plugged
into 120 VAC.
b. If it moves off the signal , it is in an effort to verify
the signal and it should return to the signal shortly.
2. Verify that you are getting the receiver’s menu
screens on the television. These screens are avail-
able with or without the dish finding the signal.
5. After the unit has verified that it has the correct
satellite, it will move to check the alternate satellite
before it completes the search routine.
3. Turn the power switch on for the MV-3500.
The dish should start moving, making one or two
revolutions before it stops to acquire GPS. This can
take a few moments or up to 10 minutes. Normal
operation will be less than a minute.
6. If you do not have signal, see Troubleshooting,
p. 11.
3
To toggle between satellites when subscribing to multi-satellite programming—
The MV-3500 will toggle between the primary and
seconday satellites for either DISH Network or
DIRECTV but not between DISH Network and
DIRECTV. Both have programming on more than
one satellite. When a channel is selected with the
remote control that is not on the satellite currently
selected, the dish will automatically move to the
correct satellite.
If this is the first time the receiver has been
used, you may need to download receiver
software; best done on a home dish.
1. While vehicle is stationary, wait for unit to ac-
quire satellite signal on satellite 119.
2. After signal is acquired, you have 6 minutes to
complete Check Switch test. Consult receiver
manual for instructions on running this test.
DIRECTV programming
1. DIRECTV receivers must be set for oval dish 2
sat selection to enable toggling between primary
101°W satellite and alternate 119°W satellite.
(Consult receiver manual for procedure.) After
receiver is set for the correct dish selection, when
you request a channel located on a different sat-
ellite, the unit will automatically move to that
satellite.
3. During the Check Switch Test, the receiver will
begin checking your switch by toggling between
satellites. When this is completed, SW42 will ap-
pear on the screen. It will be at the top of the
screen, satellite designations will be below, show-
ing odd and even transponders. See illustration
below.
DISH Network programming (DISH 500)
To set the receiver to “Switch Unknown”
NOTE: If a switch other than SW42 appears, or
you have an X in one the of the boxes below
the satellites, repeat Check Switch steps.
1. Start by disconnecting the “satellite in” cable from
back of your receiver.
4. Your system is now set up to toggle between
satellites. It will automatically move to the correct
satellite when a channel is selected.
2. With this cable disconnected, run a check switch
to clear any “previous” information out of the sys-
tem.
NOTE: Unless Check Switch was performed
on another satellite dish, such as a home
dish, you won’t need to perform this test
again.
3. The check switch should read, “No switch de-
tected” when it finishes.
4. Reconnect cable and start a new search with the
dish.
INSTALL SUMMARY
SW42
Check Switch
screen display
INPUT:
1
1
1
1
By sending in your warranty card
packed with your system, you will
SATELLITE:
POLARITY:
119
119 110 110
!
ODD EVEN ODD EVEN
receive updated information about
DISH 500 future compatibility.
STATUS:
SATELLITE RECEPTION VERIFIED
SUPERDISH
CANCEL
ALTERNATE
HELP
TEST
4
Installation Diagram
FIGURE 1
LEVELING
SCREW
ADJUSTABLE
BASE FOOT
ADJUSTABLE
BASE FOOT
REFLECTOR
LEVELING
SCREW
LIMIT
SWITCH
CABLES
CONTROL
UNIT
LNBF
GPS ANTENNA
ELEVATION
MOTOR
3 FEET MINIMUM
AZIIMUTH
MOTOR
+12VDC POWER
TO RECEIVER
LEVELING
SCREW
TO LNBF
CONNECTORS
REAR BASE FOOT MUST
BE PARALLEL TO THE
CENTER LINE OF THE
VEHICLE.
CONTROL BOX DETAIL
ELECTRONICS INTERIOR VIEW
Model MV-3500
(#1 represents Switch DOWN; #0 represents Switch up)
Sat. Rcvr.
Switch Set Position
...........................
1
2
3
4
5
6
7
8
DISH NETWORK ................................ 0 .. 0 .. 0 .. 1 .. 0 .. 0 .. 1 .. 1
DIRECTV .................................. 0 .. 0 .. 0 .. 0 .. 0 .. 0 .. 0 .. 1
(FACTORY PRESET)
RECEIVER
ExpressVu ................................. 0 .. 1 .. 0 .. 1 .. 1 .. 0 .. 1 .. 1
LNBF
P4
P3
ELEVATION
AZIMUTH
5
Parts Included • Tools Needed • How to Unpack
PARTS INCLUDED:
1 Cable entry plate
1 Radome
1 large yellow spade connector
2 small red spade connectors
All required screws and washers
1 base with electronics, dish, dual LNBF
1 tube silicone
3 base mounting feet
1 Power switch
2 Wall plates (white & brown)
1 Surface mount box
2 Cable clamps
TOOLS NEEDED FOR UNPACKING & INSTALLATION:
7/16” open end wrench
Level
Drill w/3/4” bit
1-1/4” hole saw (if mounting switch in wall)
5/16” Socket for roof screws
1/8” Allen wrench
1/2” Open end wrench
Crimping tool for coax connections
Crimping tool for electrical connections
Small blade screw driver
Pliers
Sealant (consult RV manufacturer for proper type
for your roof material)
LIFT UNIT STRAIGHT UP
UNPACKING THE UNIT
1. Open box and remove packing material.
If using knife to open
carton, BE CAREFUL.
!
Do not cut the dome on
the unit.
2. Lift unit out of box vertically. Do not turn box
and “roll” out, or turn upside down to remove.
USE 2 PEOPLE
when removing the unit
from the carton.
6
Installation
tion below.
Installing unit on roof of vehicle —
Install in DRY conditions only!
(#1 represents Switch DOWN; #0 repre-
sents Switch UP)
!
IMPORTANT! Do not install this system
in the rain, or under any wet conditions. Mois-
ture may affect electronics and void your
warranty!
Sat. Rcvr.
Switch Set Position
1
2
3
4
5
6
7 8
1. For best performance and to reduce signal ac-
quisition time, park vehicle on a level surface;
level the RV.
DIRECTV .............................................. 0 .... 0 ... 0 ..... 0 .... 0 ... 0 ..... 0 .... 1
(FACTORY PRESET)
DISH NETWORK .................................. 0 ... 0 ... 0 ..... 1 .... 0 ... 0 .... 1 .... 1
EXPRESSVU ........................................ 0 .... 1 ... 0 ..... 1 .... 1 ... 0 ..... 1 .... 1
2. Select a level spot on your roof for installation.
Obstruction Ht. Unit Clearance
Using the chart,
1
2
3
4
5
6
7
8
8” .......................................... 4”
determine the
Switches preset for
DIRECTV
10” ................................... 11.5”
minimum distances
0= UP
12” ...................................... 19”
to other equipment.
1= DOWN
15” ...................................... 32”
FIGURE 3
1
2
3
4
4
5
5
6
6
7
8
Switches set for DISH
Network
0= UP
UNIT BASE
1= DOWN
Switches set for
EXPRESSVU
1
2
3
7
8
0= UP
1= DOWN
• The unit should be no more than +/-1° off level.
• Be sure no roof-mounted equipment is
blocking the satellite “line of sight”, Fig. 3
• You will need to decide where the wires will enter
the vehicle. A coax and a power wire (minimum 16
gauge) will need to be run into the vehicle. The
power wire will go to the nearest filtered +12 VDC
power source; the coax will be routed to your
satellite receiver.
5. On each foot, screw the flange nut to the
base of the leveling screw on the mounting
foot, flange up. Place rubber washer, with the
rubber side up, on the nut, Figure 2. Push
mounting foot under base. Push foot screw
through the base and tighten lock nut to se-
cure foot to base. Be sure the base feet are
pointing away from the base. Base feet will be
removed later during install.
3. Remove screws holding dome to base and re-
move dome. Place dome in safe spot to avoid
damage. Place base on vehicle roof in the loca-
tion selected.
FIGURE 2
REMEMBER:
LEVELING SCREW
MOUNTING
REAR MOUNTING FOOT MUST BE PARALLEL
TO THE CENTER LINE OF VEHICLE.
RUBBER WASHER
FOOT
FLANGE NUT
(FLANGE UP)
4. Determine which programming you will be us-
ing. The switches for this model are preset for
DIRECTV® programming. To set the switches for
DISH Network®, or EXPRESSVU, see the illustra-
7
Installation
ROOF INSTALLATION, continued
GPS installation —
6. Place the unit on the roof in its permanent loca-
tion and mark around each base foot, Figure 4.
(Make sure the rear adjustable base foot is par-
allel to the center line of the coach.)
The GPS antenna is pre-wired and has a 3 foot
cable running through one of the connectors.
When deciding where to place GPS antenna, DO
NOT SECURE! After wiring the receiver and initializ-
ing your system, you will need to test the system.
FIGURE 4
Determine location for GPS antenna. It is recom-
mended you place the GPS antenna between unit
base and side edge of vehicle, 90° from rear
mounting bracket, at least 3 feet from dome!
Figure 6.
The recommended location for the GPS antenna
is based on having a level location and a clear
view of the sky. If another location, further from
the base, is desired, loosen the connector and
pull out additional wire in the base. You must re-
wrap and re-tie the GPS cable inside the dome
to prevent interference with the LNBF. Failure to
do so will result in malfunction! Tighten con-
nectors when done.
7. Clean roof area where the base feet will be
attached to the roof. Do not erase your marks!
8. Put approved sealant in the areas marked
for the base feet. Place base feet on top of the
sealant and screw down using (2) of the #10
screws (provided) for each foot.
9. Unscrew the locknuts in the base and re-
move the base from feet. Secure feet by
installing four more #10 screws in each base
foot.
IMPORTANT! The GPS must be located away
from obstructions on roof of vehicle. You must
have a clear view of the sky for proper opera-
tion.
10. After all base feet are secured to roof, put
sealant around edge of feet and over screws.
Replace base on leveling screws and reinstall
nut and rubber washer on leveling screw. Do
not secure until after leveling (next step).
FIGURE 6
GPS ANTENNA MOUNTED A
MINIMUM OF 3 FEET FROM
DOME.
LEVELING SCREW/
FIG
FLANGE NUT
GPS CABLE EXITS THRU
CONNECTOR
BASE EXTERIOR
FOOT
11. Leveling the base is done by tightening or loos-
ening the flange nut under the base, Figure 5.
Using an electronic level is recommended to ad-
just base so there is no more than +/- 1° off
level in all directions. Place level on base of unit if
possible. (If your level will not fit inside the base
plate, place on outside edge.) Level front to back
and side to side. Raise and lower by adjusting
flange nut under base. After leveling base, se-
cure inside base with rubber washer, rubber side
down toward base, and lock nut.
REAR MOUNTING FOOT
8
Installation • Wiring
Cable entry installation —
INSTALLING THE POWER SWITCH
1. Decide the location of the power on/off switch.
Be sure the switch is turned off before you be-
gin!
1. Decide the best location for the cables to en-
ter the vehicle, keeping in mind the desired
location for the switch and receiver.
See diagram below.
Drill a 3/4” hole in the roof, push wires inside.
Make proper connections (remember you must
have filtered +12 VDC power source).
Wall or panel mount: Drill 1-1/4” hole, pull wires
2. Place cable-entry plate over hole and cables.
Screw in place. Seal plate and screw holes with
approved sealant (not included).
through wall or panel.
Surface mount: Determine location and direction
of box. Mount box feed wire into one of the box
openings.
FIGURE 7
Select plate cover (brown or white provided) and
snap the rocker switch into the switch plate. Be sure
switch is off!
CABLE-
ENTRY
PLATE
CABLE CLAMP -
EVERY12”-16”
2. Connect filtered +12 VDC power from ve-
hicle, using red spade connector, to isolated
spade on switch.
3. Depending on the length of the cable on the
roof, you may need to use cable clamps or wire
ties (not provided) between the unit and your
cable-entry plate. Clamping the cable every 12”-
16” should eliminate any unnecessary cable
movement, Figure 7, see above.
3. Connect red power wire from MV-3500 using
red spade connector to center spade on switch.
4. Connect vehicle ground and black ground
wire, using yellow spade connector, to silver
spade on switch.
FIGURE 8
INSTALLING THE POWER SWITCH DIAGRAM
ON/OFF ROCKER
WITH LIGHT
(SHOWN IN OFF
POSITION.)
STEP 4
STEP 2
TWO BLACK GROUND WIRES
1 FROM VEHICLE
FILTERED
STEP 3
1 FROM SATELLITE DISH
+12 VDC
FROM
VEHICLE
RED POWER
WIRE SATEL-
LITE DISH
9
Installation • Wiring
Initializing & replacing the dome after
connecting the receiver(s) —
1. Be sure vehicle is in a location free of all obstruc-
tions and with a clear view of the satellite.
Connecting the receiver —
Connecting one receiver
1. Connect the coax cable from the MV-3500 to the
“SATELLITE IN” on the receiver.
2. Power up unit, turn on receiver. The unit may
take up to 10 minutes to initially find the satellite
signal. The GPS is also initializing at this time. After
the GPS initializes, the unit will begin searching for
the correct satellite.
Connecting two receivers
1. Connect the coax cable coming from the MV-
3500 to the “ SATELLITE IN” input on the primary
receiver. The primary receiver is the reciever used
most often.
3. If the GPS does not initialize at this time, turn
off the unit. You may need to move the GPS antenna
to a different location on your roof. After you move
the GPS, DO NOT SECURE TO ROOF.
2. Run a second cable through the empty Heyco
opening and connect to the ground block-type
feed through and connect the other end of this
cable to “Satellite IN” input on the second re-
ceiver.
4. TEST YOUR SYSTEM BEFORE SECURING
THE GPS ANTENNA. Make sure the TV/receiver
have the correct satellite.
5. After the correct satellite has been found, secure
GPS antenna by removing adhesive backing and
securing to roof.
GROUND BLOCK
CUSTOMER/INSTALLER
PROVIDES COAX
6. Install dome. NOTE: After connectors are tight-
ened, apply bead of silicone around the
connector where the exterior hex nut touches the
base and around the cables where they enter the
connector on the exterior of the unit. See drawing
below. If second receiver is not used, apply sili-
cone to seal center hole of third connector. See
drawing below.
CONNECTOR
PRIMARY
RECEIVER
APPLY SILICONE BEAD
AT BASE OF CONNECTOR
UNIT BASE
APPLY SILICONE BEAD IN HOLE
WHERE COAX ENTERS
USED ONLY WITH
A SECONDARY
RECEIVER
7. Insert bolts and washers in holes on dome rim.
SEE “INSTALLING DOME” below.
Installing Dome —
Insert bolts and washers (2 for
each bolt) in holes on dome
5/16” HEX
rim. Be sure bolt is vertical; not
tilted to side. Tighten to thick-
ness of top washer. Top
washer will compress, as in
drawing below.
HEAD BOLT
RUBBER
WASHERS
TOP
WASHER
BOTTOM
WASHER
5/16” HEX
HEAD
BOLT
10
Troubleshooting
SOLUTION
PROBLEM
The MV-3500 does not attempt to find a satellite
or it never moves.
1. Check your Power switch to verify that it is in the ON position.
2. Make sure that the receiver is plugged in and the satellite in jack is
connected to MV-3500.
1. Wait 10 minutes. The unit can take up to 10 minutes to acquire
GPS. If it normally takes 10 minutes to acquire GPS, contact
Winegard.
The MV-3500 turns on and moves for a few
seconds then stops and never moves again.
2. If you feel comfortable doing so, look on the roof of the vehicle to
verify that the GPS antenna is at least 3 feet from the dome and
other objects on roof. Failure to have the GPS antenna at least 3
feet away can cause the dome to interfere with GPS aquisition. If
antenna is too close, move it.
3. Check the GPS antenna cable for damage. If there is a
pinched or damaged section, contact Winegard.
The dish never stops on any of the signals that it
sees.
1. Make sure that your receiver is set up correctly.
For DISH Network, the check switch should read either “Un-
known” or “SW42”.
For DirecTV the receiver should be set for a Two Satellite Oval
Dish.
2. Make sure the receiver has power and the satellite dish is con-
nected to the “Sat In”.
With DirecTV, the dish will find the alternate
Satellite but it never finds the primary satellite.
Make sure that the Switches on the Electronics Control Box are
set for DirecTV. See page 3. These switches are found under
the dome, inside the Electronics Control Box.
The dish stopped searching but I don’t have a
signal.
1. Most likely the dish has locked on the satellite. Sometimes the
receiver refuses to show it until its ready. To help it get ready,
turn the receiver, not the dish, OFF. Wait a few minutes and
turn it back on.
2. For DISH Network users, the dish might be set to find DirecTV.
See page 3 for instructions on setting it for DISH Network.
1. Go to the check switch menu in receiver. Make sure that it’s
set for SW42 and lists both even and odd transponders on satel-
lites 110 and 119.
I am not getting all the DISH Network channels
I subscribed to.
The MV-3500 never sees any signals, it just keeps
searching.
1. Rain, Snow or excessive Dew on the dome can interrupt the
signal. Snow and Dew can be brushed off the dome. If Heavy
rain or Snow fall is blocking the signal, it may be necessary to
wait until the weather clears.
2. Check to see if the Southern sky is clear. Trees, Buildings, Large
signs or an Overpass can block the signal. Find an area where you
can be sure that this is not the problem and try again.
3. Make sure the receiver has power and the satellite dish is
connected to the “Sat In”.
11
Specifications & Warranty
Features and specifications
• One button operation.
• 30’ power cable and 30’ coaxial cable included.
• Dome is UV protected.
• GPS satellite signal acquisition.
• Depending on receiver type, access
satellites 119°, 110°, 101° or 92°.
• Off-white color compatible with all vehicles.
• Compact size —
• No user input required.
32” diameter, 15” height
Weight of unit - 43 lbs.
Shipping weight - 59 lbs.
• No data port required for any receiver.
• Elevation range 17° to 75°;
azimuth +360°. (0 - 720°)
• Functional in temperatures ranging from -13° to
+140° F.
TWO YEAR LIMITED WARRANTY
Winegard Company warrants this Winegard product (excluding receiver) against any defects in materials or
workmanship within two (2) years from date of purchase. No warranty claim will be honored unless at the time the claim
is made, you present proof of purchase to an authorized Winegard dealer (if unknown, please contact Winegard
Company, 3000 Kirkwood Street, Burlington, Iowa 52601-2000, telephone 319-754-0600).
Winegard Company (at its option) will either repair or replace the defective product at no charge to you. This warranty
covers parts, but does not cover any costs incurred in removal, shipping or reinstallation of the product. This limited
warranty does not apply if the product is damaged, deteriorates, malfunctions or fails from: misuse, improper
installation, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard,
usage not in accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or
corrosive environments such as salt spray and acid rain.
The Two Year Warranty is provided on the condition that the equipment is properly delivered with all handling and
freight charges prepaid to your Winegard dealer for repair or return to our factory at the above address. Winegard
dealers will arrange for the replacement or repair and return to you, without charge, the product which failed due to
defective material or workmanship.
WINEGARD COMPANY WILL NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED, MADE BY ANY OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD
OF THIS WRITTEN WARRANTY.
The foregoing shall be the sole and exclusive remedy of any person whether in contract, tort or otherwise, and
Winegard shall not be liable for incidental or consequential damage or commercial loss, or from any other loss or
damage except as set forth above.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Printed in U.S.A. © 2004 Winegard Company 2451019 11/09/04
12
|